 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| WWW.PHIHONG.COM 30W Power Over Ethernet Adapter High Power, high temperature single port injector. Features * * * * * * * * * * * * * Fully Compliant detection, disconnect and voltage control IEEE802.3af Diagnostic LEDs Non-Vented Case Wide temperature range -20 to +55C IP Telephones Wireless Network Access Points Blue Tooth Access Point * * * * * UNH IOL Tested Full Protection OCP, OVP Gigabit Compatible Applications Security Camera IP Print Servers Safety Approvals cUL/UL CE Korea K Argentina IRAM Length: 166mm (6.48in) Width: 80mm (3.15in) * * * * * China CCC Australia SAA & C-Tick Japan Mechanical Characteristics Height: 43.6mm (1.72in) Weight: 0.3Kg (0.5lb.) Output Specifications Model POE30U-560GHT DC Output Voltage 56V 0A Load Min. Max. 0.55A Regulation Line Load 54-57Vdc under all conditions Ripple And Noise* <500Hz 500Hz-150KHz 150KHz-500KHz 500KHz-1MHz Vp-p* 0.5 0.15 0.15 0.1 *As per IEEE802.3af Table 33-5. Phihong is not responsible for any error and change. Content is subject to change without notice. Please consult the factory and visit www.phihong.com for the most up-to-date specifications. POE30U-560GHT Characteristics INPUT: AC Input Voltage Range 90 to 264VAC WWW.PHIHONG.COM EMC FCC Part 15 Class B EN55022 Class B AC Input Voltage Rating 100 to 240VAC,47-63Hz Isolation Test Primary to Secondary: 3000VAC for 1 minute 10mA Primary to F.G.: 1500VAC for 1 minute Output to F.G.: 1500VAC AC Input Current 0.5A(RMS) max. for 90VAC 0.35A(RMS) max. for 240VAC Immunity Leakage Current 1.0 mA max. @ 254VAC 60Hz ESD: RS: EFT: Surge: CS: Voltage Dips Harmonic: EN61000-4-2. Level 3 EN61000-4-3. Level 2 EN61000-4-4. Level 2 EN61000-4-5. Level 3 EN61000-4-6. Level 2 EN61000-4-11 EN61000-3-2 AC Inrush Current 15A(RMS) max. for 115VAC 20A(RMS) max. for 230VAC OUTPUT: Total Output Power 30W Insulation Resistance Primary to secondary: >10M OHM 500VDC Primary to FC: >10M OHM 500VDC DC Offset No Data degradation with DC imbalance 18mA FEATURE: Over Voltage/Current, Short Circuit Protection Outputs equipped with short circuit protection and overload protection as per 802.3af specification except max average current is 0.55A, Peak 0.6A The output can be shorted permanently without damage Efficiency 65% (typical) at Max. load, and 120VAC 60Hz Hold-up Time 16mS min. 120VAC and max. load Indicators Led #1 indicator for input power "on" GREEN Led #2 Indicator for fault-RED Led #3 Indicator that Detected and Connected to valid IEEE802.3af load-GREEN Transient O/P Voltage Protection 60V max. ENVIRONMENTAL: Temperature Operation Non-operation -20 to +55C -40 to +71C Input Connector IEC320 inlet 3 pin Humidity Operation 5 to 90% Output Connection +pins 3,6 - pins 1,2 Dimension Diagram Unit: mm (inch) Gigabit Power Injector Block Diagram Power-up Sequence: Description of LED Functions for Gigabit Power Injector Upon power-up, all 3 LEDs will light for 2 seconds, as part of the self-test for the internal microprocessor software. After the end of the 2 seconds, the "ON" LED will illuminate green, signifying that the DC output voltage is available for powering a compliant load (to the 802.3af PoE standards). Detection Sequence: Once a compliant load is attached to the output RJ45 connector, the green "CONNECT" LED will illuminate. Should the load be non-compliant then the LEDs will blink a code signifying the cause for non-detection. Detection Failure Codes: 1. 2. 3. 4. 5. Incorrect resistive signature - The green "CONNECT" and red "FAULT" LEDs will blink 3 times. Incorrect capacitive signature - The green "ON" LED will blink 3 times. Incorrect Voffset - The green "CONNECT" and green "ON" LEDs will blink 3 times. Unstable current measurement - The green "CONNECT" LED will blink 3 times Low voltage sensed during detection (overload) - The red "FAULT" LED will blink 3 times Formatted: Indent: Left: -0.5", Hanging: 1" After the LEDs blink 3 times the PSEwill continue to try to detect a valid load. Therefore, until the correct load is applied, the LEDs will continue to blink. If there is an open circuit connected to the output RJ45 then the LEDs will not blink but the PSE will continue to try to detect a valid load. Fault Sequence: Should there be a fault such as an overload or short circuit then the red "FAULT" LED will illuminate. The red "FAULT" LED will illuminate for 2 seconds and then go off as the power supply tries to redetect a valid load. If there is a problem in detecting, the LED will indicate what is wrong with the load as per the codes in the section above.. Formatted: Indent: Left: 0.5", Right: 0.01", Tab stops: 0.5", Left |
Price & Availability of POE30U-560GHT
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |